Peptide reconstitution calculator

Units after mixing, or how much water to add. Two jobs on one page. First, the units and mL for a dose once a vial is mixed. Below it, the reverse: how much water to add to reach a concentration, or to make each dose a set number of units.

As printed on the vial label.
Bacteriostatic water, in millilitres.
As written in your instructions.
Dose unit
Syringe (U-100)

Result

Example numbers

10 units, 0.1 mL.

Syringe units10 unitson a U-100 syringe
Volume0.1 mL
Concentration5 mg/mL5,000 mcg/mL
Doses per vial20 full1 unit holds 50 mcg
0102030405060708090100 U-100 · 1 mL · 100 units

The drawing is an illustration of the arithmetic. Always read the printed scale on your own syringe.

Nothing you type is stored or sent anywhere. The arithmetic runs in your browser.

The working, with your numbers

Each step, so you can check it by hand
  1. Concentration10 mg ÷ 2 mL = 5 mg/mL (5,000 mcg/mL)
  2. Volume500 mcg ÷ 5,000 mcg/mL = 0.1 mL
  3. Syringe units0.1 mL × 100 units per mL = 10 units on a U-100 syringe

“≈” marks a value rounded for display. Working each line by hand from the numbers shown gives the same result.

Arithmetic only. This is educational arithmetic, not medical advice. Check every number against your vial label and your clinician's or pharmacy's instructions.

How much water to add

Work backwards from what you want. Both calculators round the water to 0.01 mL and show what that rounded amount gives you.

For a target concentration

Concentration unit

Water to add

Example numbers

Add 2 mL.

Water to add2 mLrounded to 0.01 mL
Concentration you get5 mg/mL5,000 mcg/mL

Nothing you type is stored or sent anywhere. The arithmetic runs in your browser.

The working, with your numbers

Each step, so you can check it by hand
  1. Water10 mg ÷ 5 mg/mL = 2 mL

“≈” marks a value rounded for display. Working each line by hand from the numbers shown gives the same result.

For a set number of units per dose

Dose unit
Syringe scale

Water to add

Example numbers

Add 2 mL; each dose is then 10 units.

Water to add2 mLrounded to 0.01 mL
Each dose is then10 unitson a U-100 syringe
Concentration2.5 mg/mL2,500 mcg/mL

Nothing you type is stored or sent anywhere. The arithmetic runs in your browser.

The working, with your numbers

Each step, so you can check it by hand
  1. Volume per dose10 units ÷ 100 units per mL = 0.1 mL
  2. Concentration needed250 mcg ÷ 0.1 mL = 2,500 mcg/mL
  3. Water5 mg ÷ 2.5 mg/mL = 2 mL

“≈” marks a value rounded for display. Working each line by hand from the numbers shown gives the same result.

Worked example

Only the arithmetic; not a suggested dose or amount of water.

A 10 mg vial. You want each mL to hold 4 mg.

  1. Water10 mg ÷ 4 mg/mL = 2.5 mL
  2. Check10 mg ÷ 2.5 mL = 4 mg/mL
  3. A 1 mg dose from it1 mg ÷ 4 mg/mL = 0.25 mL = 25 units

What reconstitution changes, and what it does not

Many peptides are sold as a dry powder. Adding liquid (reconstituting) turns the powder into a solution you can measure with a syringe. The amount of compound in the vial stays exactly what the label says. What you choose is the volume it is spread through, and that sets the concentration.

A smaller volume makes a stronger solution: each dose is fewer units, which can be hard to measure when it gets under a couple of units. A larger volume makes each dose a bigger, easier number, but uses more of the syringe and the vial. The calculator warns at both ends: under 1 unit, and more than the syringe holds. Follow your product or pharmacy instructions on the liquid to use and how to mix it.

For the full method, read how reconstitution math works, and for what the water itself is, what bacteriostatic water is.

Questions about the arithmetic

How much bacteriostatic water should I add to a peptide vial?

There is no single right amount; the water only sets the concentration. Your instructions or pharmacy should tell you. If you want a particular concentration or a particular number of units per dose, the "how much water to add" calculators on this page work backwards from that target.

How do I work out water for a target concentration?

Divide the amount in the vial by the concentration you want. 10 mg ÷ 5 mg per mL = 2 mL. Keep both in the same unit of weight: 5 mg at 2,000 mcg per mL is 5,000 mcg ÷ 2,000 = 2.5 mL.

How do I work out water so each dose is a set number of units?

Turn the units into mL (units ÷ 100 on a U-100 syringe), divide the dose by that volume to get the concentration you need, then divide the vial amount by that concentration. For a 5 mg vial, a 250 mcg dose and 10 units per dose: 10 ÷ 100 = 0.1 mL; 250 mcg ÷ 0.1 mL = 2,500 mcg per mL; 5,000 mcg ÷ 2,500 = 2 mL.

Why does the water result get rounded?

You cannot measure 2.3333 mL. The calculator rounds to 0.01 mL and then shows the concentration and units you actually get with the rounded amount, so the small difference is visible rather than hidden.

Does more water mean a weaker dose?

No. More water spreads the same amount of compound through more liquid. Each mL holds less, so the same dose takes more units, but the dose itself is unchanged.

Never miss the dose you just worked out

Get Kept